New Products
)
)
)
Compact and easy to use
One, two or three channels – the R&S®HMC804x DC Power supplies with their specifications and wide range of functions are ideal for use in development labs and industrial environments. Thanks to their high energy efficiency, the linear power supplies remain cool and quiet, even at maximum load. Practical interfaces and connectors allow users to work quickly and conveniently with the R&S®HMC804x. Comfort functions enable the instruments to be used in special applications.
모델
| 모델명 | 출력 채널 수 | 최대 출력 파워 | 채널 당 출력 전압 | 채널 당 출력 전류 |
| R&S®HMC8041 | 1 | 100 W | 0 V to 32 V | 10 A |
| R&S®HMC8041G | 1 | 100 W | 1 V to 32 V | 10 A |
| R&S®HMC8042 | 2 | 50 W | 0 V to 32 V | 5 A |
| R&S®HMC8042G | 2 | 50 W | 0 V to 32 V | 5 A |
| R&S®HMC8043 | 3 | 33 W | 0 V to 32 V | 3 A |
| R&S®HMC8043G | 3 | 33 W | 0 V to 32 V | 3 A |
주요특징
- Clear display of all measured parameters
- Galvanically isolated, floating and short-circuit proof outputs
- Protective functions adjustable for each channel
- Ideal power supply for hardware developers and labs
- Remote control
Flexible channel configuration
All channels are galvanically isolated and can be combined to drive balanced ircuitries or for higher voltages/currents.
Front panel: 4mm safety sockets (R&S®HMC8041 including SENSE)
Rear panel: WAGO cage clamp for all channels including SENSE Convenient parallel and serial operation
Clear display of all measured parameters
The brilliant color display shows voltage, current and power values in real time with a Brilliant QVGA color display (320 x 240 pixel), realtime voltage, current and power values, a high setting and readback resolution: 1mV and 0.1mA/1.0mA (depending on current and model). Also there is low residual ripple due to linear postregulation and high energy efficiency, low heat dissipation and quiet fan.
Flexible overcurrent protection
FuseLink allows you to freely combine the electronic fuses in each channel. A fuse delay can be set to prevent too early switch-off due to a short current spike. Overcurrent/overvoltage protection can be set for each channel individually. The electronic fuses can be linked to other channels. In this case, the channel exceeding the maximum current level and all linked channels will be switched off. Even the delay time can be set to prevent premature switch-off due to short current spikes.
Programmable sequences
Arbitrary waveforms can be generated for voltage and current. Function can be configured and executed via control panel or external interface.
EasyRamp function
Sometimes test sequences should avoid the abrupt rise of the supply voltage. The EasyRamp function allows users to run a linear startup curve within a defined time span.
Remote control
Remote control is possible via USB and LAN. The HMC804x-G models offer IEEE-488 (GPIB) interface additionally.
주요 스펙
| Electrical specifications | ||
| Number of output channels | 1/2/3 | |
| Total output power | max. 100 W | |
| Maximum output power per channel | 100 W/50 W/33 W | |
| Output voltage per channel | 0 V to 32 V | |
| Maximum output current per channel | 10 A/5 A/3 A | |
| Voltage ripple and noise (20 Hz to 20 MHz) | R&S®HMC8041: < 1 mV (RMS); R&S®HMC8042/43: < 450 µV (RMS) | |
| Current ripple and noise (20 Hz to 20 MHz) | R&S®HMC8041: < 1.5 mA (RMS) (meas.); R&S®HMC8042/43: < 1 mA (RMS) (meas.) | |
| Load recovery time*1) | < 1 ms (meas.) | |
| Programming/readback resolution | Voltage | 1 mV |
| Current | < 1 A: 0.1 mA (R&S®HMC8041: 0.5 mA); ≥ 1 A: 1 mA | |
| Readback accuracy (± (% of output + offset)) | Voltage | < 0.05% + 2 mV |
| Current | typ. < 0.05% + 4 mA (R&S®HMC8041: typ. < 0.15% + 10 mA) | |
| Special functions | ||
| Measurement functions | voltage, current, power, energy | |
| Protection functions | OVP, OCP, OPP, OTP | |
| FuseLink function | ● | |
| Fuse delay at power-up | ● | |
| Sense function | ● | |
| Sink mode | – | |
| Output sequencing | ● | |
| Trigger input/output | ● | |
| Arbitrary function | ● (EasyArb) | |
| Analog/modulation interface | ● | |
| Data logging | ● | |
| Display and interfaces | ||
| Display | 3.5" QVGA | |
| Rear panel connections | connector block with 4 lines per channel | |
| Remote control interfaces | standard: USB, LAN; R&S®HMC804x-G models with IEEE-488 (GPIB) | |
| General data | ||
| Dimensions (W × H × D) | 222 × 97 × 291 mm | |
| Weight | 2.6 kg | |
| Rack installation | R&S®HZC95 option | |
| *1) 10% to 90% load change within a band of ± 20 mV of set voltage. | ||
문서 자료
| 제목 | 다운받기 |
|---|---|
| R&S ®HMC804x DC 파워서플라이- 데이터시트 | 다운로드 |
사업자등록번호 : 220-86-72761대표이사 : 신동만대표전화 : 070-7872-0701팩스 : 02-2167-3801
(우)07299 서울특별시 영등포구 경인로 775 (문래동 3가, 에이스하이테크시티 3동 2층)
(우)07299 서울특별시 영등포구 경인로 775 (문래동 3가, 에이스하이테크시티 3동 2층)